STI EZ Firestop Grommet Easily Fire Protect a Single Category 6 Cable 10 Pack EZ-Firestop® Grommets make sealing penetrations of individual and small bundles of cables through gypsum board walls a snap. Molded from premium plenum-plastics and...

Arlington FB248SC T-Box for Suspended Ceiling Grids Note: This units is for fans and fixtures up to 70lbs.  They changed it from the catalog sheet and it comes with a metal gang box on the top as shown in the video below. Metal hanger. For...

Arlington F428SC T-Box for Suspended Ceiling Grids Note: This box is for mounting fixtures less than 50lbs.  It does not come with the metal gang box on the top. Arlington's T-Box is the cost effective way to mount a fan or fixture on a suspended...

LV1RP our super-sturdy, low-voltage mounting bracket, installs class 2 low voltage wiring with a 3.5" hole saw in less than a minute! Also available, 2-gang LV2RP. It installs just as fast with a 4.5" hole saw.  Check out the video to see how fast...

The easy to install single-gang LV1XL offers the same great features as our popular LV series of mounting brackets, but the screws are extra-long to handle thick walls. Built-in features like these deliver a betterlooking job... For use with up to...

3/4" "J" cable support hooks are versatile and can be attached to a wide variety of structures using beam clamps, clips and other support components. These support hooks eliminate the problem of point loads that can cause band width damage to sensitive...

The Raceway System Designed to Give You an Extra HAND Wire Hider Non-Metallic Surface Mount Raceway was designed with the Installation Professional in mind. Have you ever laid cable into a raceway only to have it fall out as you attempt to close the...

The Raceway System Designed to Give You an Extra HAND Wire Hider Non-Metallic Surface Mount Raceway was designed with the Installation Professional in mind. Have you ever laid cable into a raceway only to have it fall out as you attempt to close the...

Ideal for Heavy Loads in Hollow Walls, Ceilings & Floors TOGGLER toggle bolts pre-install without a bolt and can be installed with a screw gun. This allows one-person installations (instead of two), saving time and money. It's like having an extra...

The LV1LP is a low profile bracket that can be used to secure telephone jacks and coaxial cable jacks to walls for proper installation.  Use these brackets for installations where there is limited space behind the drywall or wall board. ...

The LV1 can be used to secure telephone jacks and coaxial cable jacks to walls for proper installation. Non-conductive, smooth plastic construction For communications, cable TV, computer wiring CAT 5 listed Adjusts to fit 1/4" to 1" thick...

Features: Use polypropylene line with manual or power fishing systems for light duty cable or rope pulling applications Ready to use storage container quickly dispenses a tangle free line and also protects line from direct sunlight Line is resistant...

2" "J" cable support hooks are versatile and can be attached to a wide variety of structures using beam clamps, clips and other support components. These support hooks eliminate the problem of point loads that can cause band width damage to sensitive...

1-5/16" "J" cable support hooks are versatile and can be attached to a wide variety of structures using beam clamps, clips and other support components. These support hooks eliminate the problem of point loads that can cause band width damage to...

Low voltage dry wall retrofit bracket takes the place of a single gang outlet box. Can be used for volume controls, switches or wall plates. Great to use when adding equipment to existing structures. Class 2 low voltage wiring only Cannot be used for...

Hammond BUSBAR4X10 Copper Ground Bar Kit 4" x 10" Features Electro Tin Plated Copper Bus Bar, 100/300 micro inches of plating. The thin tin coating acts as a shield, inhibiting copper oxidization. Copper oxidization causes a poor electrical...

Hammond BUSBAR2X10 Copper Ground Bar Kit 2" x 10" Features Electro Tin Plated Copper Bus Bar, 100/300 micro inches of plating. The thin tin coating acts as a shield, inhibiting copper oxidization. Copper oxidization causes a poor electrical...

SC100RR Low Voltage Mounting Bracket Non Metallic Retrofit PVC construction for durable performance Designed for low-voltage devices in an existing wall Installs vertically or horizontally

Just nail or screw these non-metallic brackets to a wood or steel stud – and you’re ready to install low voltage Class 2 wiring! Lower cost than extension rings or mud rings Ready to install - nails or screws come parkedin-...

Just nail or screw these non-metallic brackets to a wood or steel stud – and you’re ready to install low voltage Class 2 wiring! Lower cost than extension rings or mud rings Ready to install - nails or screws come parkedin- place Built-in...